Total Dissolved Solids (TDS) in Commercial Pools: When to Drain and Why It Matters

Total dissolved solids, or TDS, is the combined concentration of everything dissolved in your pool water, measured in parts per million. As a general industry guideline, you partially drain and refill once TDS climbs roughly 1,500 ppm above your fresh fill water, because past that point the dissolved load starts working against your chlorine, your water clarity, and your equipment.

Most operators test chlorine and pH every day and never think about TDS until the water looks dull, the chlorine demand creeps up, or a service tech mentions the number is high. By then the pool has usually been telling you for weeks. Understanding what TDS is, where it comes from, and when it actually matters keeps you from either ignoring a real problem or draining a pool that did not need it.

What Total Dissolved Solids Actually Measures

TDS is the sum of every dissolved substance in the water: the minerals in your fill water, the byproducts left behind by chlorine and pH chemicals, dissolved calcium and salts, and the organic load that bathers add. It is reported in parts per million, the same unit you already use for chlorine and alkalinity, but the numbers are far larger. A freshly filled pool might read a few hundred ppm, while a heavily used pool late in the season can climb into the thousands.

The key idea is that most of these solids never leave on their own. When water evaporates, the dissolved solids stay behind and concentrate. Every bag of calcium hypochlorite, every jug of acid, and every swimmer adds a little more. Filtration removes suspended particles you can see, but it does nothing to dissolved material, so TDS only rises over the life of the water unless you dilute it.

TDS is not itself a sanitizer or a balance parameter you adjust up and down. It is a running total of how much the water has been through. That is why operators treat it as a signal: a high reading tells you the water is old and loaded, not that one specific chemical is off.

Why TDS Climbs in a Commercial Pool

Commercial pools build TDS faster than residential ones for simple reasons: more bathers, more chemical dosing, and more evaporation from heating and high use. Three sources do most of the work.

Source water. Your starting point is whatever comes out of the tap. In hard-water regions like Las Vegas, fill water already carries a meaningful mineral load before you add anything. That is your baseline, and it is why the guideline is written as an amount above fill water rather than a single universal ceiling.

Chemical additions. Every sanitizer and balancing product leaves dissolved residue. Cal hypo adds calcium, liquid chlorine and some pH adjusters add dissolved salts, and stabilizer and alkalinity products all contribute. The more you dose to hold a busy pool in range, the faster TDS accumulates.

Bather load and evaporation. Swimmers introduce sweat, body oils, and other organics, and evaporation steadily concentrates everything already dissolved. A hotel pool running warm all year with steady traffic is effectively boiling its water down over months, leaving the solids behind.

Salt pools are a special case. A salt chlorine generator relies on dissolved salt that typically runs around 3,000 ppm, so a salt pool starts with a high TDS reading by design. That salt is supposed to be there, so the drain decision is based on how far TDS has risen above the intended salt level, not the raw number.

How High TDS Affects Water Quality and Equipment

TDS matters because of what happens when it gets too high, not because of the number itself. Four effects show up most often.

Weaker sanitizer. As dissolved solids concentrate, free chlorine has a harder time doing its job at the same reading. You may hold free chlorine in the standard 1 to 3 ppm range and still see slow response to contamination, because the crowded water interferes with how efficiently the chlorine works. Operators often react by pushing chlorine higher, which adds even more dissolved product and makes the underlying problem worse.

Dull or cloudy water. Very high TDS can leave water looking flat and hazy even when your other tests are in range. If you have chased a cloudy pool through chlorine, pH, and filtration without a clear cause, elevated TDS is worth checking. Our guide on troubleshooting cloudy commercial pool water walks through the full order of checks.

Scaling or corrosion. TDS is one of the inputs to the Langelier Saturation Index, the calculation that predicts whether water will scale or corrode. A high dissolved load shifts that balance and can push borderline water toward depositing scale on surfaces and equipment or becoming aggressive toward metal. If you are not already running the number, see how to calculate the Langelier Saturation Index.

Salty or off taste. At high levels the water can taste salty or flat and feel different to swimmers. In a non-salt pool, a salty taste is a clue that TDS has climbed well beyond where it should be.

Total Dissolved Solids: When to Dilute A running total of everything dissolved in the water, measured in ppm What TDS Is Minerals, chemical residue and organics, added up in ppm Dilute At +1,500 ppm above fresh fill water Salt Pools Baseline already holds about 3,000 ppm salt by design What high TDS does Weaker Sanitizer Chlorine responds more slowly Dull Water Hazy look with tests in range Scale or Corrosion Shifts the saturation index balance The only cure is dilution Partial drain and refill, or reverse osmosis. No chemical removes TDS. cpopro.com ยท PHTA Certified CPO Instructor

How to Test TDS and Read the Number

TDS is measured with a handheld TDS or conductivity meter, not a reagent test kit. The meter reads how well the water conducts electricity, which tracks closely with dissolved content, and reports a ppm value in seconds. Calibrate the meter per the manufacturer and rinse the probe between readings so you are not carrying solids from one sample to the next.

Record your fill water TDS when you first fill or after a large refill. That baseline is the number every later reading is compared against. Without it you are guessing whether a reading of, say, 1,800 ppm is normal for your source water or a sign the pool is overdue for dilution. Testing TDS monthly is enough for most commercial pools, with an extra check if chlorine demand rises, the water goes dull, or you are deep into a heavy season. Log it alongside your daily chemistry so the trend is visible, the same way you keep your other testing documentation and records.

Train the Operators Who Make These Calls

Knowing when a reading means act and when it means wait is what a Certified Pool Operator is trained to do. Get your team PHTA certified and confident on water balance.

See Upcoming Test Dates

How to Lower TDS When It Is Too High

There is no chemical that removes dissolved solids. Once TDS is high, you have two real options, and both come down to replacing loaded water with cleaner water.

Partial drain and refill. This is the standard approach. You lower the pool part way and top it off with fresh water, which dilutes the dissolved load back toward your baseline. How much you remove depends on how far over you are, and you follow your local health code and water-use rules for draining a commercial pool. After refilling, rebalance from the ground up: alkalinity to 80 to 120 ppm, pH to the 7.2 to 7.6 target, calcium hardness to 200 to 400 ppm, and free chlorine back into the 1 to 3 ppm range. Fresh fill water changes all of these, so do not skip the full rebalance.

Reverse osmosis. In drought regions or where draining large volumes is restricted or expensive, mobile reverse osmosis services filter the existing pool water through membranes that strip out dissolved solids and return low-TDS water to the pool. It conserves water and avoids a full drain, at a higher per-service cost. For a large hotel or HOA pool in a water-restricted area, it can be the more practical route.

Whichever path you take, the goal is the same: bring the dissolved load back down so your sanitizer works efficiently and your water balance behaves predictably. Diluting at the right time is cheaper and easier than fighting a loaded pool with ever-larger chemical doses, and it protects the surfaces and equipment the saturation index is meant to safeguard.

Frequently Asked Questions

What is the maximum TDS for a commercial pool?

Rather than a single universal ceiling, the common industry guideline is to partially drain and refill once TDS rises about 1,500 ppm above the level of your fresh fill water. Because fill water varies by region, you measure and record your baseline first, then compare later readings to it. Always follow your local health code, which may set its own limit.

Does high TDS mean my chlorine will not work?

Not exactly. Your chlorine still works, but at high TDS it tends to respond more slowly at the same free chlorine reading, so contamination clears less efficiently. Hold free chlorine in the standard 1 to 3 ppm range and keep pH at the 7.2 to 7.6 target. If the pool still struggles to hold sanitizer, check TDS as part of the diagnosis.

Why is my salt pool TDS so high?

A salt pool is supposed to have high TDS. The salt a chlorine generator needs typically runs around 3,000 ppm, and that salt is counted in the TDS reading. For a salt pool, judge TDS by how far it has climbed above the intended salt level, not by the raw number, since the salt itself belongs there.

Can I lower TDS without draining?

The only ways to lower TDS are dilution with fresh water or mobile reverse osmosis. No chemical removes dissolved solids. Reverse osmosis filters the existing water and returns it with the solids stripped out, which conserves water where draining is restricted, while a partial drain and refill is the simpler and lower-cost option where water use allows it.

Total dissolved solids is the quiet background number that tells you how hard your water has been working. Record your fill water baseline, check TDS monthly, and partially drain and refill once it climbs roughly 1,500 ppm above that baseline. Do that, and you keep your chlorine efficient, your water clear, and your surfaces protected, without chasing symptoms that trace back to water that was simply overdue for dilution.

Samuel Holmes, PHTA Certified CPO Instructor

Written by

Samuel Holmes

PHTA Certified CPO Instructor since 2017. 14 years in the swimming pool industry. Built and sold two pool companies. Still on pool decks every week.

Full bio →